Jl-audio TR650-CSi Manuel d'utilisateur télécharger pdf (Page 3)

INSTALLING THE WOOFERS IN

CUSTOM LOCATIONS:

Run speaker wire to the desired mounting

location. If you are running wires into a door, use

existing factory wiring boots whenever possible. If

you are drilling new holes, file their edges and install

rubber grommets into each hole. Then, cover the

wires with a protective PVC sleeve and run them

through the door jamb. Make sure that the wires

will clear door hinges and other structures in the

door. If you are unsure about any part of this

process, please contact your JL AUDIO dealer for

installation help.

Double check the clearance for both speakers

before proceeding.

Use the supplied template on the top of the

product packaging to mark the desired mounting

location. Mark the center and the outline of the

mounting hole as well as the mounting screw

positions. Before drilling or cutting, use a utility knife

to cut any fabric, vinyl or leather from hole

locations. These materials can easily be snagged by

a drill or a saw, causing damage to the panel and

possible bodily injury.

Drill four 1/8" (3 mm) holes for the speaker’s

mounting screws at the positions you have marked.

Also drill a pilot hole in the center of the speaker

mounting hole at this time. Then, using a saber saw,

hole saw or nibbler, make the circular cut out for

the speaker. File any rough edges.

Insert the mounting clips with the flat side

towards the speaker as shown in the diagram.

It is absolutely vital that the speaker frame fits

into the mounting hole cleanly. This must be

checked prior to tightening the screws. Do not

force the frame into a hole that is too small! Do

not tighten the speaker onto an uneven surface! This

will damage your speakers. The speaker should also

fit so that no air leaks around the mounting flange.

Air leaks will cause a severe degradation in sound

quality. Seal any air leaks with silicone, rope caulk or

similar sealant material.

Connect the speaker wires, observing correct

polarity, and install the speaker and grille tray as

shown.

Hand-tighten the screws evenly to avoid

bending the speaker frame!

Break off small pieces of the supplied butyl

adhesive putty and place them on the inside of each

grille tray. This adhesive will hold the grille in place

firmly and prevent rattling. Then insert the metal

grille into the grille tray, squeezing gently around its

edge until it seats firmly into the tray.

JL AUDIO TR650-CSi 5

INSTALLING THE WOOFERS IN

FACTORY LOCATIONS:

If you will be using the factory speaker wires, it

may be necessary to change the terminations. This

may be accomplished by using an adaptor plug or

simply by cutting the factory connector off and

using the supplied crimp connectors to terminate

the speaker wires.The large connector is for the

positive terminal and the small connector is for the

negative terminal of each woofer. Make sure that

you observe correct polarity in your connections. If

you are unsure about any of these issues, contact

your JL AUDIO dealer for installation assistance.

Your new speakers have been designed to install,

without modifications, into most vehicles that accept

a 6.5-inch (160 mm) speaker. Most factory 6.5-inch

speakers use four mounting screws which will line

up with the mounting holes on your woofers.

Others use a 3-hole mounting system which is

accommodated by a separate set of mounting holes

on the frames of your TR650-CWi woofers.

It is absolutely vital that the speaker frame fits

into the mounting hole cleanly. This must be

checked prior to tightening the screws. Do not

force the frame into a hole that is too small! Do

not tighten the speaker onto an uneven surface! This

will damage your speakers. The speaker should also

fit so that no air leaks around the mounting flange.

Air leaks will cause a severe degradation in sound

quality. Seal any air leaks with silicone, rope caulk or

similar sealant material.

Install as shown in the diagram here.

Use the supplied mounting clips unless the

factory holes already feature threaded inserts.

Hand-tighten the screws evenly to avoid bending

the speaker frame!

4 JL AUDIO TR650-CSi

1 2 3 4 5

Commentaires sur ces manuels

Pas de commentaire

Jl-audio TR650-CSi Manuel d'utilisateur Page 3

Commentaires sur ces manuels

Produits connexes et manuels pour Acoustique Jl-audio TR650-CSi