Jl-audio TR650-CSi Manuel d'utilisateur télécharger pdf (Page 2)

BUILT-IN TWEETER

PROTECTION CIRCUITRY:

The TR Crossover networks are equipped with

an advanced electronic tweeter protection circuit

designed to minimize the possibility of tweeter

failure. This electronic device monitors current going

to the tweeter and will disconnect the tweeter from

the signal when it senses overload. Should this occur

while listening to the audio system, simply reduce the

volume for a few seconds and the protection circuit

will reset itself automatically.

SPEAKER PLACEMENT

CONSIDERATIONS:

A component system gives you the ability to

place the woofer and tweeter separately in your

vehicle interior.This can be good or bad, depending

on how it’s done.

As a general rule, the tweeters should be placed

relatively close to the woofers for best tonal balance

and most coherent imaging (the closer, the better).

Any separation greater than 8 inches (20 cm) is

likely to result in degraded sound quality.

Avoid placing tweeters where they will be

blocked by objects in the interior of the car

(including seated occupants). When selecting a

mounting location, look at both sides of the car to

make sure that this location is clear on both sides.

You can always experiment with tweeter

placement before committing to a final mounting

location. Simply connect the rest of the system and

allow plenty of wire length for the tweeters. Using

velcro or similar material, attach the tweeters in

different locations until you find the one where they

perform best.

Woofers will usually be placed into factory

speaker locations. If you have some woofer

mounting flexibility, keep the followiing in mind:

Lower mounting locations, such as the lower front

corner of a door or a kick-panel provide the

greatest path length distances for the sound emitted

by the woofer. For this reason, they are generally

more desirable than higher mounting locations.

Higher mounting locations will usually result in

extreme near-side soundstage bias which

compromises the stereo listening experience.

JL AUDIO TR650-CSi 3

Less Desirable More Desirable

TR650-CSi SPECIFICATIONS:

Woofers: Injection-molded, mica-filled, polypropylene

cone body, 1-inch (25mm) voice coil, flat-profile/

symmetrical-roll spider, butyl rubber surround.

Tweeters: 0.50-inch (12 mm) textile dome

diaphragm, integral phase plug, neodymium magnet,

ferrofluid cooled and damped. Designed for flush

or surface mounting.

Crossover Design: Natural roll-off low pass

(woofer), 1st order high-pass circuit with electrolytic

capacitor on tweeter. Polyswitch tweeter protection.

Continuous Power Handling:

50 Watts (RMS Method)

Recommended Amplifier Power:

10-75 Watts per channel (RMS Method)

Frequency Response: 59 Hz - 22 KHz (± 3 dB)

Efficiency @ 1W/1m: 91.0 dB

Nominal Impedance: 4 ohms

Included Components and Parts:

• Two TR650-CWi 6.5-inch (160 mm) Woofers

• Two TR050-CT 0.50-inch (12 mm) Tweeters

• Two TR050-CThp In-Line, High-Pass Filters on

5.3 ft. (1.6 m) Wire Harnesses

• Two Metal Spring Clips (for tweeter

flush mounting)

• Two Surface-Mount Tweeter Fixtures

• Two Metal Woofer Grilles and Grille Trays

• Butyl Adhesive Putty (for woofer grilles)

• Eight #8 x 1 1/4-inch (30 mm)

Sheet Metal Screws

• Four #6 x 5/8” (16 mm) Sheet Metal Screws

• Two 1/4-inch (6 mm) Machine Screws

• Eight Mounting Clips (for woofer mounting)

• Two 5.2 mm Female Crimpable Connectors

• Two 2.8 mm Female Crimpable Connectors

GETTING STARTED:

• Turn off the audio system. It is also advisable to

disconnect the negative (-) terminal of your

vehicle’s battery whenever performing

installation work.

• Before cutting, drilling or inserting any screw,

check clearances on both sides of the planned

mounting surface. Also check for any potential

obstacles, such as window tracks and motors,

wiring harnesses, etc. Check both sides of the car,

many cars are not symmetrical!

• Always wear protective eyewear.

It is absolutely vital that your component

system is connected as shown in the diagram

below. Failure to connect the system as shown

will result in damage to your speakers which is

NOT covered under warranty. Do not substitute

different crossover networks or filters into your

TR650-CSi System. Only use in-line filters clearly

marked “TR050-CThp”.

WARNING

2 JL AUDIO TR650-CSi

A) Wiring Diagram:

1 2 3 4 5

Commentaires sur ces manuels

Pas de commentaire

Jl-audio TR650-CSi Manuel d'utilisateur Page 2

Commentaires sur ces manuels

Produits connexes et manuels pour Acoustique Jl-audio TR650-CSi